tidyfox Review

This product can only be shipped to certain zip codes. View full details page for more information.

View Full Details

This item is out of stock.

Gorgeously looking vent hood
 from United States,  May 16, 2012

The hood came well packaged and in two large boxes. I did lots of internet searching looking for the right range hood, but kept coming back to this one due to the 900 CFM Centrifugal blower and the curved glass. Electronic buttons did not make difference in my selection. I would actually prefer regular buttons for the simplicity and operational reliability. The Installation Manual is omitting a lot of information about the installation, it is basically useless. It does not even specify power plug location other than a 35W breaker size with a USA/Canada code that is not sufficient to a person who did not install an Euro style range hood before. I ended up installing the plug between the 6" duct tube and stainless steel chimney enclosure mounted per a code to the drywall. It supposed to be accessible. Removing screws that hold the SS chimney and the SS chimney be itself could/should be considered as accessible. The power wire is not visible this way and makes the Range Hood look professionally installed, which we did by ourselves. Our kitchen has soffits. This made the installation little more challenging. We had to cut one of the lower SS chimney wall shorter to make it fit under the soffit and to meet the minimum 28" distance of the hood from the stove. The upper SS chimney is not installed at all. Venting the range hood into an attic is not recommended. This was another challenge for us as the original hood was venting into an attic (house was built in 1950's). The unit by itself is heavy and needs to be attached to 2x4's with 4" screws to avoid vibration noise, not only to drywall with the included sheet rock fasteners. They are to be put into wall to hold the hood while mounting it. This is a challenge if you don't hit the studs with one of the existing holes on the main mounting plate/back plate, which is attached permanently to the hood already. I had to take some parts off the hood apart to be able to drill holes for a proper attachment to 2x4's. I used special drill bits to drill the holes. Even doing that bulged out the back panel of the hood slightly. I hope this won't become a problem in the future. The SS chimneys attach to wall via Chimney mounting bracket. The bracket is not one piece as in the Manual, but 2 pieces instead. I would prefer one piece that could be attached to a 2x4 with one screw that did not happen. Again, I hope this will not become a problem in the future. The SS chimney walls aren't that heavy, I just wonder if it won't get loose in the future. My other half and me both like a good craftsmanship and try to install everything properly for the products to be enjoyed without problems that could pop up later due to improper installation. While I called the 800 phone number about the different Chimney mounting brackets and let me tell you, the young man representing the company was very rude right from the beginning. He said: "Do you see another part in the box that is not in the Manual?" And he went on with more up nosed comments and answers. So I asked him to drop the disrespectful insulting attitude. I also told him that the Manuals being sent with the hoods need to be updated to show the correct hardware included in the package. Not everybody has money to get a Wall Mounted Hood installed by a professional. The lights used in this unit seem to be warm white version of MR16 35W halogen bulbs. It is not a light we are used to, it is not strong enough to really see into the pots while cooking. I need to see what I am cooking, not just to have an accent light on the back wall. My other half is using it for an early morning light to make a coffee in dimmed light conditions, it is just fine for that. I will be looking into it if I can replace them with cool warm lights or anything else to make the lights brighter. While using this vent hood we found a glitch with the lights. They are flickering in 3 different strengths. This is very annoying and is caused most likely to the buttons not being sealed properly. I read about this problems on the cheap models and thought that this double priced model would not have this problem. I was very wrong. I hope I can find an answer to this problem on the internet so I can fix it. The light button is so sensitive to a touch, you don't have to even press it. I hope it will not brake in the future while it is too sensitive to my taste. The other buttons are fine and you have to press them just a tiny bit to activate a function. We are overall happy with its gorgeous look and the smooth fan function. We hope the hood will be pleasing us day after day in our newly remodeled kitchen. PROS: Seems to be quality craftsmanship Range Hood Hood is running very smoothly in all 6 speeds. Gorgeously looking hood. Good price for 900 CFM CONS: The lights are very weak and too yellow, they are only accent lights. Lights flicker in 3 different strengths while boiling water/fluids or heavier steaming. Fan speed #6 won't stop it. Poor Installation Manual PS: As I was looking on the internet for a better installation manual I found out that this Cavaliere model is also being sold under name SPAGNA VETRO 30-inch Wall-Mounted Stainless Steel Glass Range Hood - SV218D-30. If you need better lights and positioned in the front of the hood instead against the wall, get an Electrolux RH30WC60GS model with 600 CFM. The Installation, the Parts, and the dimensions PDF for the Electrolux model is also much more in detail than Cavaliere. But the price is not as good though.

  • How did the color on site compare with the actual product? exactly
  • Please tell us about the quality of the product. good quality, light have problems flickering in 3 different strengths if boiling water or steaming. The light is too weak to use for cooking, it is just for looks.
Was This Review Helpful?