My husband had both hips replaced this summer, which led to the idea of getting a hot tub, which led to us building a gorgeous covered patio to house the hot tub...you get the idea! We wanted something small with all the features found in the nicer hot tubs. I don't plan on entertaining guests in my hot tub! I researched several local hot tub stores, hot tub companies, features, warranties..etc. We decided to take a gamble for the low price, about $2000 less than our local hot tub store for a nice 3 person tub. This tub is manufactured in the US and has all the features we were looking for...pump motor size, jets, lights. The little waterfall is ok...nothing to wow me, but, I don't care about that feature.. I gave it only 4 stars now as we just got it running! My husband is 6' and I'm 5'7" tall. It would be nice if it were deeper; but, it works for us...we just slide down a bit. And, again, we saved money up front. It heated up in chilly weather in a couple hours. We will be thrilled if it works well for 6+years, as we're not taking it with us when we move! We patiently waited for delivery...it took awhile...but, we didn't care as our project was under construction. The delivery folks were AWESOME...exceeded my expectations.
Purchased this hot tub for our patio. Delivery was quick. I called customer service to ensure I set up the tub properly and purchased the correct chemicals. The service team was extremely helpful. Super happy with the purchase. Can't beat it for the price.
Finally got the hot tub. Ordered July 3rd, delivered August 28th. Overstock had no clue as to why the delay. Called the manufacturer, Leisure Products, at *** and was told that the delay was due to their cover supplier. Overstock needs to do better on their tracking. I got a shipped email with a tracking button that had no tracking info. Kudos to the freight company, ABF. The driver helped me load it on to my pickup and then on to my deck. The tub’s freight weight with the cover and pallet was 645 lbs. It ships on its side banded to a long custom size pallet that just fit on my pickup with the tailgate down. It is wrapped in heavy plastic with only thin cardboard and some foam for protection. We slid the tub on rugs on its shipping side to its spot on my deck, and then myself and 3 neighbors tilted it down onto a 6’ 2 x 4 and lifted it up by the slight edge on the bottom of the side panel just enough to slide the 2 x 4 out. The manual and the power cord are behind the panel under the control panel. READ the manual first. A PITA taking the panel off and putting it back on. With a cordless drill, I notched out a 7/16” hole in the bottom beam and the panel for the power cord. A few tips: Do not use power tools to remove and install the screws from the side panel. I used a ratchet screwdriver. Fill the tub up through the filter hole before you re-install the side panel to check for leaks. Do not plug the power cord in until the tub is full. Make sure the 2 slice valves are in the default locked up position before plugging it in. This tub weighs ~600 lbs. empty. You will need at least 4-5 helpers. Filled, ~300 gallons, it weighs ~3100 lbs., not including people weight, so if you place it on a deck you need adequate support. I added 2- 8’ 4 x 6s across the joists a few inches in from the hot tub’s edge with 6-4 x 6 posts, 2 extra 4 x 6 posts on my center beams, and a 4 x 6 post on the outer joist next to the house. Check the suction drain cover. Mine had ~20 clogged holes. A small center screw holds it on. A PITA to remove when the tub is full but I am assuming this is a safety feature. When you first plug it in it goes through a self-check test. After the test, you should see Pr (priming mode) on the control panel, which should last ~6 minutes before the pump starts to run. I purchased my hot tub chemicals at Leslie’s Pool Supplies They are nationwide, check lesliespool.com’s store locator. I went with a bromine bundle, test strips, and a floater dispenser instead of a starter kit. More expensive but will last a lot longer. They will do a free 9 point water test on your hot tub water in the store and tell you what chemicals you need. I bought my Confer Plastics espresso color steps from an eBay vendor for $56. shipped. Great quality, made in USA. Pros: Ok hot tub for the price. Got it for $2250. with free shipping, no tax, during their July 4th sale. Seats 4 people comfortably, 6 small people maybe. It is advertised as 110V Plug and Play but you need a dedicated outlet and a 20 amp breaker for that outlet. More than adequate jet flows on high pump speed setting. Nice cover and color, perfect fit, not too heavy, 1 person can remove it; also comes with locking buckles that screw to the side panels. It comes with a pre-installed filter. Good comprehensive manual. It took ~8 hours to heat the water from 74F to 101F, not bad for only 110V. 7 color changing underwater LED light can be set to show only 1 color. Cons: A few nitpicks. The tub was undamaged but the side panels have scuffmarks, not from us, and I had to repaint the black base that had multiple nicks in it down to the bare wood. The manufacturer needs to improve their QC. The inside of tub was very dirty. Cardboard packing on the bottom panel was soaked presumably from a pre-test. It is 110V and does not come with an auxiliary heater so it takes a while to heat to set temp. There should be a better way to access the manual and power cord then taking a side panel off. It is advertised as having a 10’ power cord but only ~7’ of that is useful (see pics). My outlet is 5’ from the tub and ~2’ high and it just reaches. The GFI plug is large. I had to dremel out the opening in my outlet to get it to fit.
If you need further help or information please visit our Online Help Center