Pyle PT4001X 5500-watt Professional DJ Amplifier

First and foremost: This amplifier is NOT 5500 watts. Don't be mesmerized and fooled by insultingly inaccurate large numbers. The only way this amp could produce 5500 watts is If Lightning Strikes it (i.e. 5500 Watts I.L.S.). In reality, it's producing a maximum of about 250 continuous RMS watts per channel at 8 Ohms. That means don't embarrass yourself by posting videos on Youtube claiming that you have a 5000, 10000, 50000 watt stereo system in your bedroom that is running off of a standard 110 volt / 15 - 20 amp circuit breaker...OOPS! Pros: This amp is simple and produces good, clean, and powerful sound at high volumes without distorting nor overheating. The cooling design is great. There are two 60mm fans inside the front of the chassis. Each fan is attached to a large square tubular heatsink (one on each side of the chassis) that extends the entire depth of the chassis. All of the MOSFETS (8 per side) are attached to these large fan cooled heatsinks. I've rocked out on this amp for hours and although it was warm (105 - 110 degrees), I could still comfortably put my hand on top of it. Another great quality of this amp is that it feels well built. It's nice and heavy (about 40 pounds), and it feels very solid and sturdy. If you want a simple amplifier that you can hook up to your PC (via 3.5mm to RCA patch cable), use as a home stereo system, or just need something powerful to take to an outdoor party, then this amplifier is for you. Cons: It's only a 2 channel amp. I would have liked it to be a 4 channel amp, but I knew it was only 2 channel before I purchased the unit; so I can't complain much. Also, there is a push button circuit breaker on the rear of the chassis. It would be a nice feature, but it doesn't seem to do much good. It feels very cheap and flimsy. I've actually blown the internal fuses without the amp setting off the rear circuit breaker. Maybe I have a defective unit, but either way, it doesn't seem to be functional. Finally, it would have been nice if there were more than one set of RCA inputs on the unit. Other Thoughts: I'm tired of underpowered home theater receivers (from Sony, Onkyo, ect) that overheat and can't produce good quality sound at moderate to high volume levels. Consequently, I bought this Pyle Pro PT4001X amplifier for my home stereo system. So far, I'm very pleased with it. Package Contents: Amp, manual, and power cord. The power cord is the same type of power cord that you might find on your computer's power supply unit and monitor. *Side Note* This amplifier uses 4 (2 per side) 5 X 20mm 8 Amp / 250 Volt fast-blow fuses. Specs according to the manual: Continuous Output RMS Wattage in Stereo Mode:260 watts x 2 (20 Hz - 20 kHz, 8 ohms) 400 watts x 2 (1 kHz, 4 ohms) Continuous Output Power in Bridged Mode: 700 watts x 1 (20 Hz - 20 kHz, 8 ohms) 800 watts x 1 (1 kHz, 8 ohms) T.H.D.: 0.1% * Frequency Response +/- 3 dB: 10 Hz - 50 kHz Input Sensitivity (for rated output power): 1.0V Signal-to-Noise Ratio (A-Weighted): 100 dB Impedance: Stereo 4-16 ohms, Bridged 8-16 ohms Power Requirement: 120 VAC, 60 Hz Dimensions: 5 3/16" H x 19" W x 13" D

• How did the image on site compare with the actual product? The image of the front of the product matched exactly.
• Was the product free of any manufacturer defects? The only MANUFACTURER defect was the reset/fuse switch on the back of the unit.
• Please tell us about the quality of the product. The overall quality of this product is good. The only problem is Overstock and UPS damaged (dented/dropped) the unit.